Schedule A Service

Everyone has their own unique conception about A Step-by-Step Guide to Installing a Bathtub.

Installing a bath tub isn't exactly brain surgery, but it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately tough job. If the old tub is easily accessible, the project can relocate rapidly; if you have to open a wall to eliminate the old bathtub as well as position the new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will require an assistant to move out the old tub and also set in the brand-new one. See to it you have actually qualified yourself for the task as well as fit trying it. Instead of hiring a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one prior to you start. Chances are you may require an expert plumber to make tube connections.
This write-up will assist you mount a new bath tub in your bathroom if you have actually already bought a brand-new bathtub and also don't need to alter the plan of your previous water supply pipes.
Your tools as well as material checklist must comprise the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installation, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of removing the existing taps can be fairly problematic as a result of the restricted gain access to that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the staying water that will come from the pipelines. When the supply pipes have been eliminated, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old securing substance.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

Suitable New Taps

If the tails of the new faucets are plastic, then you will need a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and also the sink. Safeguard the tap in place with the supplier given backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical tap connectors. The former type should be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.

Setting up the Bath tub

Making use of the two wooden boards under its feet, put the bathtub in the called for position. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
The following objective is to make sure that the bath tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub up until the spirit level reads degree.
To install taps, fit the bottom of the outermost flexible faucet port to the ideal supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the supply of water as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if necessary. Load the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub needs to wait till the bathtub has been utilized a minimum of when as this will resolve it into its last placement.

Planning for the Installation

First of all, the sustaining framework supplied with the bath should be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its final position.

Tiling Around the Tub

In the area where the bathroom satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a stiff seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, leading to problems with moisture and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched paper or soft rope. Remember to always load the bathtub with water prior to securing, to permit the motion experienced when the tub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water resistant glue as well as cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I'm very fascinated with How to Install a Bathtub Yourself and I hope you appreciated my blog posting. Do you know about somebody else who is fascinated by the topic? Do not hesitate to share it. I treasure reading our article about How to Install a Bathtub Yourself.

Go Deal